[ 0.000000] Linux version 5.15.0 (oe-user@oe-host) (riscv64-pine64-linux-gcc (GCC) 11.3.0, GNU ld (GNU Binutils) 2.38.20220708) #1 SMP Thu Apr 13 06:38:09 UTC 2023 [ 0.000000] OF: fdt: Ignoring memory range 0x40000000 - 0x40200000 [ 0.000000] Machine model: Pine64 Star64 [ 0.000000] earlycon: sbi0 at I/O port 0x0 (options '') [ 0.000000] printk: bootconsole [sbi0] enabled [ 0.000000] Reserved memory: created CMA memory pool at 0x0000000080000000, size 512 MiB [ 0.000000] OF: reserved mem: initialized node linux,cma, compatible id shared-dma-pool [ 0.000000] Zone ranges: [ 0.000000] DMA32 [mem 0x0000000040200000-0x00000000ffffffff] [ 0.000000] Normal [mem 0x0000000100000000-0x000000013fffffff] [ 0.000000] Movable zone start for each node [ 0.000000] Early memory node ranges [ 0.000000] node 0: [mem 0x0000000040200000-0x00000000c010ffff] [ 0.000000] node 0: [mem 0x00000000c0110000-0x00000000c01fffff] [ 0.000000] node 0: [mem 0x00000000c0200000-0x000000013fffffff] [ 0.000000] Initmem setup node 0 [mem 0x0000000040200000-0x000000013fffffff] [ 0.000000] SBI specification v0.3 detected [ 0.000000] SBI implementation ID=0x1 Version=0x10000 [ 0.000000] SBI TIME extension detected [ 0.000000] SBI IPI extension detected [ 0.000000] SBI RFENCE extension detected [ 0.000000] SBI v0.2 HSM extension detected [ 0.000000] CPU with hartid=0 is not available [ 0.000000] CPU with hartid=0 is not available [ 0.000000] riscv: base ISA extensions acdfim [ 0.000000] riscv: ELF capabilities acdfim [ 0.000000] percpu: Embedded 18 pages/cpu s33896 r8192 d31640 u73728 [ 0.000000] pcpu-alloc: s33896 r8192 d31640 u73728 alloc=18*4096 [ 0.000000] pcpu-alloc: [0] 0 [0] 1 [0] 2 [0] 3 [ 0.000000] Built 1 zonelists, mobility grouping on. Total pages: 1033735 [ 0.000000] Kernel command line: earlyprintk console=tty1 console=ttyS0,115200 rootwait earlycon=sbi root=/dev/mmcblk1p4 [ 0.000000] Unknown command line parameters: earlyprintk [ 0.000000] Dentry cache hash table entries: 524288 (order: 10, 4194304 bytes, linear) [ 0.000000] Inode-cache hash table entries: 262144 (order: 9, 2097152 bytes, linear) [ 0.000000] mem auto-init: stack:off, heap alloc:off, heap free:off [ 0.000000] software IO TLB: mapped [mem 0x00000000fbfff000-0x00000000fffff000] (64MB) [ 0.000000] Memory: 3440300K/4192256K available (11207K kernel code, 6131K rwdata, 6144K rodata, 2189K init, 395K bss, 227668K reserved, 524288K cma-reserved) [ 0.000000] SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=4, Nodes=1 [ 0.000000] rcu: Hierarchical RCU implementation. [ 0.000000] rcu: RCU restricting CPUs from NR_CPUS=8 to nr_cpu_ids=4. [ 0.000000] rcu: RCU debug extended QS entry/exit. [ 0.000000] Tracing variant of Tasks RCU enabled. [ 0.000000] rcu: RCU calculated value of scheduler-enlistment delay is 10 jiffies. [ 0.000000] rcu: Adjusting geometry for rcu_fanout_leaf=16, nr_cpu_ids=4 [ 0.000000] NR_IRQS: 64, nr_irqs: 64, preallocated irqs: 0 [ 0.000000] CPU with hartid=0 is not available [ 0.000000] riscv-intc: unable to find hart id for /cpus/cpu@0/interrupt-controller [ 0.000000] riscv-intc: 64 local interrupts mapped [ 0.000000] plic: plic@c000000: mapped 136 interrupts with 4 handlers for 9 contexts. [ 0.000000] random: get_random_bytes called from start_kernel+0x4c4/0x6de with crng_init=0 [ 0.000000] riscv_timer_init_dt: Registering clocksource cpuid [0] hartid [1] [ 0.000000] clocksource: riscv_clocksource: mask: 0xffffffffffffffff max_cycles: 0x1d854df40, max_idle_ns: 881590404240 ns [ 0.000001] sched_clock: 64 bits at 4MHz, resolution 250ns, wraps every 2199023255500ns [ 0.008236] clocksource: timer@13050000.ch0: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 79635851949 ns [ 0.018459] clocksource: timer@13050000.ch1: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 79635851949 ns [ 0.028772] clocksource: timer@13050000.ch2: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 79635851949 ns [ 0.039087] clocksource: timer@13050000.ch3: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 79635851949 ns [ 0.049599] Console: colour dummy device 80x25 [ 0.055309] printk: console [tty1] enabled [ 0.059373] Calibrating delay loop (skipped), value calculated using timer frequency.. 8.00 BogoMIPS (lpj=40000) [ 0.069579] pid_max: default: 32768 minimum: 301 [ 0.074434] Mount-cache hash table entries: 8192 (order: 4, 65536 bytes, linear) [ 0.081859] Mountpoint-cache hash table entries: 8192 (order: 4, 65536 bytes, linear) [ 0.091096] ASID allocator disabled [ 0.094629] rcu: Hierarchical SRCU implementation. [ 0.100248] smp: Bringing up secondary CPUs ... [ 0.106371] smp: Brought up 1 node, 4 CPUs [ 0.111561] devtmpfs: initialized [ 0.122386] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 19112604462750000 ns [ 0.132195] futex hash table entries: 1024 (order: 4, 65536 bytes, linear) [ 0.152388] pinctrl core: initialized pinctrl subsystem [ 0.158454] NET: Registered PF_NETLINK/PF_ROUTE protocol family [ 0.165003] thermal_sys: Registered thermal governor 'step_wise' [ 0.165333] cpuidle: using governor menu [ 0.196431] platform soc:dsi-output: Fixing up cyclic dependency with 29400000.dc8200 [ 0.204695] platform 295d0000.mipi: Fixing up cyclic dependency with soc:dsi-output [ 0.212711] platform 29590000.hdmi: Fixing up cyclic dependency with 29400000.dc8200 [ 0.256375] HugeTLB registered 1.00 GiB page size, pre-allocated 0 pages [ 0.263037] HugeTLB registered 2.00 MiB page size, pre-allocated 0 pages [ 0.273316] vgaarb: loaded [ 0.276198] SCSI subsystem initialized [ 0.280064] usbcore: registered new interface driver usbfs [ 0.285545] usbcore: registered new interface driver hub [ 0.290886] usbcore: registered new device driver usb [ 0.296382] mc: Linux media interface: v0.10 [ 0.300602] videodev: Linux video capture interface: v2.00 [ 0.306369] Advanced Linux Sound Architecture Driver Initialized. [ 0.313618] clocksource: Switched to clocksource riscv_clocksource [ 0.327262] NET: Registered PF_INET protocol family [ 0.332718] IP idents hash table entries: 65536 (order: 7, 524288 bytes, linear) [ 0.344054] tcp_listen_portaddr_hash hash table entries: 2048 (order: 4, 81920 bytes, linear) [ 0.352625] TCP established hash table entries: 32768 (order: 6, 262144 bytes, linear) [ 0.360865] TCP bind hash table entries: 32768 (order: 8, 1048576 bytes, linear) [ 0.369388] TCP: Hash tables configured (established 32768 bind 32768) [ 0.376138] UDP hash table entries: 2048 (order: 5, 196608 bytes, linear) [ 0.383112] UDP-Lite hash table entries: 2048 (order: 5, 196608 bytes, linear) [ 0.390735] NET: Registered PF_UNIX/PF_LOCAL protocol family [ 0.396977] RPC: Registered named UNIX socket transport module. [ 0.402836] RPC: Registered udp transport module. [ 0.407623] RPC: Registered tcp transport module. [ 0.412367] RPC: Registered tcp NFSv4.1 backchannel transport module. [ 0.419588] PCI: CLS 0 bytes, default 64 [ 0.423974] Unpacking initramfs... [ 0.424419] Initialise system trusted keyrings [ 0.432293] workingset: timestamp_bits=62 max_order=20 bucket_order=0 [ 0.445394] NFS: Registering the id_resolver key type [ 0.450406] Key type id_resolver registered [ 0.454661] Key type id_legacy registered [ 0.458801] nfs4filelayout_init: NFSv4 File Layout Driver Registering... [ 0.465485] nfs4flexfilelayout_init: NFSv4 Flexfile Layout Driver Registering... [ 0.472963] ntfs: driver 2.1.32 [Flags: R/W]. [ 0.477632] jffs2: version 2.2. (NAND) \xc2\xa9 2001-2006 Red Hat, Inc. [ 0.484407] fuse: init (API version 7.34) [ 0.528716] NET: Registered PF_ALG protocol family [ 0.533469] Key type asymmetric registered [ 0.537637] Asymmetric key parser 'x509' registered [ 0.542643] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 249) [ 0.550065] io scheduler mq-deadline registered [ 0.554621] io scheduler kyber registered [ 0.559451] start plist test [ 0.562862] end plist test [ 0.661011] clk-starfive-jh7110 13020000.clock-controller: starfive JH7110 clkgen init successfully. [ 0.671357] L2CACHE: DataError @ 0x00000000.08040140 [ 0.676359] L2CACHE: DataFail @ 0x00000000.0804005B [ 0.681278] L2CACHE: No. of Banks in the cache: 8 [ 0.685996] L2CACHE: No. of ways per bank: 16 [ 0.690396] L2CACHE: Sets per bank: 256 [ 0.694308] L2CACHE: Bytes per cache block: 64 [ 0.698803] L2CACHE: Index of the largest way enabled: 15 [ 0.700447] Initramfs unpacking failed: invalid magic at start of compressed archive [ 0.704582] jh7110-pmu 17030000.power-controller: registered 8 power domains [ 0.730084] Freeing initrd memory: 14372K [ 0.787460] Serial: 8250/16550 driver, 6 ports, IRQ sharing disabled [ 0.797285] @@#########################@@ [ 0.807864] @@ dev ptr:ffffffe0bfedec00/1500/1 [ 0.812494] PVR_K: 1: Read BVNC 36.50.54.182 from HW device registers [ 0.819064] PVR_K: 1: RGX Device registered BVNC 36.50.54.182 with 1 core in the system [ 0.828384] PVR_K: 1: RGX Firmware image 'rgx.fw.36.50.54.182' loaded [ 0.838397] PVR_K: 1: Shader binary image 'rgx.sh.36.50.54.182' loaded [ 0.847226] [drm] Initialized pvr 1.17.6210866 20170530 for 18000000.gpu on minor 0 [ 0.864023] loop: module loaded [ 0.869381] spi-nor spi0.0: gd25lq128d (16384 Kbytes) [ 0.880972] 3 fixed-partitions partitions found on MTD device 13010000.spi.0 [ 0.888001] Creating 3 MTD partitions on "13010000.spi.0": [ 0.893523] 0x000000000000-0x000000040000 : "spl" [ 0.900025] 0x000000100000-0x000000400000 : "uboot" [ 0.906439] 0x000000f00000-0x000001000000 : "data" [ 0.913874] libphy: Fixed MDIO Bus: probed [ 0.918928] CAN device driver interface [ 0.923285] starfive-eth-plat 16030000.ethernet: force_sf_dma_mode is ignored if force_thresh_dma_mode is set. [ 0.933622] starfive-eth-plat 16030000.ethernet: User ID: 0x41, Synopsys ID: 0x52 [ 0.941056] starfive-eth-plat 16030000.ethernet: DWMAC4/5 [ 0.946604] starfive-eth-plat 16030000.ethernet: DMA HW capability register supported [ 0.954496] starfive-eth-plat 16030000.ethernet: RX Checksum Offload Engine supported [ 0.962370] starfive-eth-plat 16030000.ethernet: Wake-Up On Lan supported [ 0.969289] starfive-eth-plat 16030000.ethernet: TSO supported [ 0.975121] starfive-eth-plat 16030000.ethernet: Enable RX Mitigation via HW Watchdog Timer [ 0.983519] starfive-eth-plat 16030000.ethernet: Enabled Flow TC (entries=1) [ 0.990631] starfive-eth-plat 16030000.ethernet: TSO feature enabled [ 0.997043] starfive-eth-plat 16030000.ethernet: Using 40 bits DMA width [ 1.242554] libphy: stmmac: probed [ 1.245945] YT8531 Gigabit Ethernet stmmac-0:00: attached PHY driver (mii_bus:phy_addr=stmmac-0:00, irq=POLL) [ 1.255896] YT8531 Gigabit Ethernet stmmac-0:01: attached PHY driver (mii_bus:phy_addr=stmmac-0:01, irq=POLL) [ 1.267110] starfive-eth-plat 16040000.ethernet: force_sf_dma_mode is ignored if force_thresh_dma_mode is set. [ 1.277407] starfive-eth-plat 16040000.ethernet: User ID: 0x41, Synopsys ID: 0x52 [ 1.284863] starfive-eth-plat 16040000.ethernet: DWMAC4/5 [ 1.290375] starfive-eth-plat 16040000.ethernet: DMA HW capability register supported [ 1.298284] starfive-eth-plat 16040000.ethernet: RX Checksum Offload Engine supported [ 1.306169] starfive-eth-plat 16040000.ethernet: Wake-Up On Lan supported [ 1.313065] starfive-eth-plat 16040000.ethernet: TSO supported [ 1.318904] starfive-eth-plat 16040000.ethernet: Enable RX Mitigation via HW Watchdog Timer [ 1.327323] starfive-eth-plat 16040000.ethernet: Enabled Flow TC (entries=1) [ 1.334416] starfive-eth-plat 16040000.ethernet: TSO feature enabled [ 1.340814] starfive-eth-plat 16040000.ethernet: Using 40 bits DMA width [ 1.585672] libphy: stmmac: probed [ 1.589020] YT8531 Gigabit Ethernet stmmac-1:00: attached PHY driver (mii_bus:phy_addr=stmmac-1:00, irq=POLL) [ 1.599024] YT8531 Gigabit Ethernet stmmac-1:01: attached PHY driver (mii_bus:phy_addr=stmmac-1:01, irq=POLL) [ 1.610826] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver [ 1.617344] ehci-pci: EHCI PCI platform driver [ 1.621858] ehci-platform: EHCI generic platform driver [ 1.627768] usbcore: registered new interface driver cdc_acm [ 1.633368] cdc_acm: USB Abstract Control Model driver for USB modems and ISDN adapters [ 1.641499] usbcore: registered new interface driver cdc_wdm [ 1.648040] starfive-rtc 17040000.rtc: registered as rtc0 [ 1.653515] i2c_dev: i2c /dev entries driver [ 1.657995] usbcore: registered new interface driver uvcvideo [ 1.683647] thermal thermal_zone0: failed to read out thermal zone (-110) [ 1.690689] starfive-wdt 13070000.wdog: Heartbeat: timeout=15, count/2=180000000 (0aba9500) [ 1.700237] sdhci: Secure Digital Host Controller Interface driver [ 1.706401] sdhci: Copyright(c) Pierre Ossman [ 1.710815] Synopsys Designware Multimedia Card Interface Driver [ 1.717190] sdhci-pltfm: SDHCI platform and OF driver helper [ 1.723291] ledtrig-cpu: registered to indicate activity on CPUs [ 1.729654] jh7110-sec 16000000.crypto: Unable to request sec_m dma channel in DMA channel [ 1.737903] jh7110-sec 16000000.crypto: Cannot initial dma chan [ 1.744157] usbcore: registered new interface driver usbhid [ 1.749677] usbhid: USB HID core driver [ 1.753693] usbcore: registered new interface driver rtl8852bu [ 1.759667] riscv-pmu-sbi: SBI PMU extension is available [ 1.765050] riscv-pmu-sbi: 15 firmware and 4 hardware counters [ 1.770897] riscv-pmu-sbi: Perf sampling/filtering is not supported as sscof extension is not available [ 1.780729] usbcore: registered new interface driver snd-usb-audio [ 1.788895] NET: Registered PF_INET6 protocol family [ 1.795040] Segment Routing with IPv6 [ 1.798665] In-situ OAM (IOAM) with IPv6 [ 1.802698] NET: Registered PF_PACKET protocol family [ 1.807782] can: controller area network core [ 1.812237] NET: Registered PF_CAN protocol family [ 1.817033] can: raw protocol [ 1.820047] can: broadcast manager protocol [ 1.824318] can: netlink gateway - max_hops=1 [ 1.829186] 9pnet: Installing 9P2000 support [ 1.833446] Key type dns_resolver registered [ 1.838574] Loading compiled-in X.509 certificates [ 1.881494] starfive_jh7110-pinctrl 13040000.gpio: SiFive GPIO chip registered 64 GPIOs [ 1.890300] starfive_jh7110-pinctrl 17020000.gpio: SiFive GPIO chip registered 4 GPIOs [ 1.898424] pl08xdmac 16008000.sec_dma: initialized 8 virtual memcpy channels [ 1.905544] pl08xdmac 16008000.sec_dma: initialized 16 virtual slave channels [ 1.914527] debugfs: Directory '16008000.sec_dma' with parent 'dmaengine' already present! [ 1.922776] pl08xdmac 16008000.sec_dma: DMA: PL080 rev0 at 0x16008000 irq 23 [ 1.930145] ssp-pl022 10060000.spi: ARM PL022 driver for StarFive SoC platform, device ID: 0x00041022 [ 1.939354] ssp-pl022 10060000.spi: mapped registers from 0x0000000010060000 to (____ptrval____) [ 1.948583] ssp-pl022 10060000.spi: Requested frequency: 10000000 Hz is unsupported,select by default 8250000 Hz [ 1.959121] ssp-pl022 10060000.spi: will use autosuspend for runtime pm, delay 100ms [ 1.973958] rtc-hym8563 2-0051: registered as rtc1 [ 1.979674] rtc-hym8563 2-0051: setting system clock to 2023-04-30T13:12:56 UTC (1682860376) [ 1.990171] at24 5-0050: supply vcc not found, using dummy regulator [ 1.997311] at24 5-0050: 512 byte 24c04 EEPROM, writable, 16 bytes/write [ 2.006660] axp15060-regulator 5-0036: Register mipi_0p9 done! vol range:900 ~ 900 mV [ 2.016392] axp15060-regulator 5-0036: Register hdmi_1p8 done! vol range:1800 ~ 1800 mV [ 2.026320] axp15060-regulator 5-0036: Register hdmi_0p9 done! vol range:900 ~ 900 mV [ 2.036498] axp15060-regulator 5-0036: Register cpu_vdd done! vol range:500 ~ 1540 mV [ 2.047516] pcie_plda 2c000000.pcie: host bridge /soc/pcie@2C000000 ranges: [ 2.054513] pcie_plda 2c000000.pcie: MEM 0x0038000000..0x003fffffff -> 0x0038000000 [ 2.062613] pcie_plda 2c000000.pcie: MEM 0x0980000000..0x09bfffffff -> 0x0980000000 [ 2.070807] ATR entry: 0x09c0000000 -> 0x0000000000 [0x0010000000] (param: 0x000001) [ 2.078556] ATR entry: 0x0038000000 -> 0x0038000000 [0x0008000000] (param: 0x000000) [ 2.086355] ATR entry: 0x0980000000 -> 0x0980000000 [0x0040000000] (param: 0x000000) [ 2.513880] pcie_plda 2c000000.pcie: Port link down, exit. [ 2.533303] clk-starfive-jh7110-vout 295c0000.clock-controller: starfive JH7110 clk_vout init successfully. [ 2.555011] clk-starfive-jh7110-isp 19810000.clock-controller: starfive JH7110 clk_isp init successfully. [ 2.565217] dw_axi_dmac_platform 16050000.dma-controller: DesignWare AXI DMA Controller, 4 channels [ 2.575301] printk: console [ttyS0] disabled [ 2.599746] 10000000.serial: ttyS0 at MMIO 0x10000000 (irq = 17, base_baud = 1500000) is a 16550A [ 2.608659] printk: console [ttyS0] enabled [ 2.616975] printk: bootconsole [sbi0] disabled [ 2.628142] xhci-hcd xhci-hcd.1.auto: xHCI Host Controller [ 2.633703] xhci-hcd xhci-hcd.1.auto: new USB bus registered, assigned bus number 1 [ 2.641900] xhci-hcd xhci-hcd.1.auto: hcc params 0x200073c8 hci version 0x100 quirks 0x0000002000018010 [ 2.651397] xhci-hcd xhci-hcd.1.auto: irq 53, io mem 0x10110000 [ 2.657639] xhci-hcd xhci-hcd.1.auto: xHCI Host Controller [ 2.663164] xhci-hcd xhci-hcd.1.auto: new USB bus registered, assigned bus number 2 [ 2.670888] xhci-hcd xhci-hcd.1.auto: Host supports USB 3.0 SuperSpeed [ 2.678297] hub 1-0:1.0: USB hub found [ 2.682109] hub 1-0:1.0: 1 port detected [ 2.686570] usb usb2: We don't know the algorithms for LPM for this host, disabling LPM. [ 2.695390] hub 2-0:1.0: USB hub found [ 2.699206] hub 2-0:1.0: 1 port detected [ 2.703778] cdns3-starfive 10210000.usbdrd: usb mode 1 3.0 probe success [ 2.710724] jh7110-vin 19800000.vin_sysctl: stfcamss probe enter! [ 2.720523] jh7110-vin 19800000.vin_sysctl: stfcamss probe success! [ 2.737949] dwmmc_starfive 16010000.sdio0: IDMAC supports 32-bit address mode. [ 2.743964] dwmmc_starfive 16020000.sdio1: IDMAC supports 32-bit address mode. [ 2.745285] dwmmc_starfive 16010000.sdio0: Using internal DMA controller. [ 2.752472] dwmmc_starfive 16020000.sdio1: Using internal DMA controller. [ 2.759235] dwmmc_starfive 16010000.sdio0: Version ID is 290a [ 2.759268] dwmmc_starfive 16010000.sdio0: DW MMC controller at irq 29,32 bit host data width,32 deep fifo [ 2.766042] dwmmc_starfive 16020000.sdio1: Version ID is 290a [ 2.771896] mmc_host mmc0: card is non-removable. [ 2.781471] dwmmc_starfive 16020000.sdio1: DW MMC controller at irq 30,32 bit host data width,32 deep fifo [ 2.801670] mmc_host mmc1: card is polling. [ 2.801769] jh7110-sec 16000000.crypto: will run requests pump with realtime priority [ 2.815931] jh7110-sec 16000000.crypto: Initialized [ 2.821530] starfive-i2s 120b0000.i2stx_4ch0: designware: play supported [ 2.828346] starfive-i2s 120b0000.i2stx_4ch0: designware: i2s master mode supported [ 2.836329] sf-mipi-dphy-tx 295e0000.mipi-dphy: sf_dphy_probe begin [ 2.842606] sf-mipi-dphy-tx 295e0000.mipi-dphy: ===> sf_dphy_probe enter, 445 [ 2.849917] sf-mipi-dphy-tx 295e0000.mipi-dphy: control ECO [ 2.855518] sf-mipi-dphy-tx 295e0000.mipi-dphy: supply mipi_1p8 not found, using dummy regulator [ 2.864487] sf-mipi-dphy-tx 295e0000.mipi-dphy: sf_dphy_probe end [ 2.870688] cdns-dsi 295d0000.mipi: dsi_sys_clk = 297000000 [ 2.876440] cdns-dsi 295d0000.mipi: starfive dsi bind end [ 2.883552] of_cfs_init [ 2.886097] of_cfs_init: OK [ 2.889260] starfive-pwmdac 100b0000.pwmdac: clk_apb0 = 49500000, clk_pwmdac_apb = 49500000, clk_pwmdac_core = 4068493 [ 2.900315] cfg80211: Loading compiled-in X.509 certificates for regulatory database [ 3.013647] mmc_host mmc0: Bus speed (slot 0) = 198000000Hz (slot req 400000Hz, actual 399193HZ div = 248) [ 3.014260] cfg80211: Loaded X.509 cert 'sforshee: 00b28ddf47aef9cea7' [ 3.023661] usb 1-1: new high-speed USB device number 2 using xhci-hcd [ 3.023665] mmc_host mmc1: Bus speed (slot 0) = 198000000Hz (slot req 400000Hz, actual 399193HZ div = 248) [ 3.032480] platform regulatory.0: Direct firmware load for regulatory.db failed with error -2 [ 3.054827] cfg80211: failed to load regulatory.db [ 3.236080] hub 1-1:1.0: USB hub found [ 3.240004] hub 1-1:1.0: 4 ports detected [ 3.241249] random: fast init done [ 3.256179] starfive soc:display-subsystem: bound 29400000.dc8200 (ops 0xffffffff81077a98) [ 3.264546] innohdmi-starfive 29590000.hdmi: inno hdmi bind begin [ 3.272407] innohdmi-starfive 29590000.hdmi: [drm:inno_hdmi_bind] registered Inno HDMI I2C bus driver success [ 3.282620] innohdmi-starfive 29590000.hdmi: HDMI&AUDIO register done. [ 3.289247] innohdmi-starfive 29590000.hdmi: inno hdmi bind end [ 3.295239] starfive soc:display-subsystem: bound 29590000.hdmi (ops 0xffffffff81078830) [ 3.303384] vs-simple-encoder soc:dsi-output: encoder_bind begin [ 3.309491] no panel, -517 [ 3.312232] vs-simple-encoder soc:dsi-output: encoder_bind error [ 3.318291] starfive soc:display-subsystem: bound soc:dsi-output (ops 0xffffffff81078478) [ 3.327303] [drm] Initialized starfive 1.0.0 20191101 for soc:display-subsystem on minor 1 [ 3.335782] starfive soc:display-subsystem: [drm] Cannot find any crtc or sizes [ 3.343481] starfive soc:display-subsystem: [drm] Cannot find any crtc or sizes [ 3.350910] starfive soc:display-subsystem: [drm] Cannot find any crtc or sizes [ 3.360770] mmc_host mmc1: Bus speed (slot 0) = 198000000Hz (slot req 50000000Hz, actual 49500000HZ div = 2) [ 3.370674] mmc1: new high speed SDHC card at address 5048 [ 3.377028] mmcblk1: mmc1:5048 SD32G 29.7 GiB [ 3.389418] mmcblk1: p1 p2 p3 p4 [ 3.473724] mmc_host mmc0: Bus speed (slot 0) = 198000000Hz (slot req 300000Hz, actual 300000HZ div = 330) [ 3.673736] usb 1-1.1: new high-speed USB device number 3 using xhci-hcd [ 3.905719] hub 1-1.1:1.0: USB hub found [ 3.909801] hub 1-1.1:1.0: 4 ports detected [ 3.913685] mmc_host mmc0: Bus speed (slot 0) = 198000000Hz (slot req 200000Hz, actual 200000HZ div = 495) [ 4.113754] usb 1-1.2: new high-speed USB device number 4 using xhci-hcd [ 4.370587] BUG: spinlock bad magic on CPU#3, kworker/3:0/28 [ 4.373739] mmc_host mmc0: Bus speed (slot 0) = 198000000Hz (slot req 100000Hz, actual 100000HZ div = 990) [ 4.376402] lock: 0xffffffd004fc1080, .magic: 00000000, .owner: /-1, .owner_cpu: 0 [ 4.394412] CPU: 3 PID: 28 Comm: kworker/3:0 Not tainted 5.15.0 #1 [ 4.400673] Hardware name: Pine64 Star64 (DT) [ 4.405076] Workqueue: usb_hub_wq hub_event [ 4.409339] Call Trace: [ 4.411827] [] dump_backtrace+0x1c/0x24 [ 4.417295] [] dump_stack_lvl+0x40/0x58 [ 4.422759] [] dump_stack+0x14/0x1c [ 4.427869] [] spin_dump+0x62/0x6e [ 4.432890] [] do_raw_spin_lock+0xb0/0xd0 [ 4.438542] [] _raw_spin_lock+0x1a/0x22 [ 4.444008] [] pq_push+0xa4/0xf8 [ 4.448868] [] _phl_ser_mdl_init+0x102/0x268 [ 4.454784] [] bk_module_init+0x26/0xbc [ 4.460242] [] dispr_register_module+0x10a/0x344 [ 4.466503] [] phl_disp_eng_register_module+0x30/0x78 [ 4.473198] [] phl_register_ser_module+0x1c/0x62 [ 4.479462] [] rtw_phl_init+0x10bc/0x12e4 [ 4.485112] [] rtw_hw_init+0x4a/0x1ba [ 4.490416] [] rtw_dev_probe+0x4e8/0x86e [ 4.495980] [] usb_probe_interface+0xcc/0x254 [ 4.501980] [] really_probe+0x94/0x39a [ 4.507359] [] __driver_probe_device+0x76/0x12e [ 4.513518] [] driver_probe_device+0x2c/0xb0 [ 4.519432] [] __device_attach_driver+0x74/0xe0 [ 4.525591] [] bus_for_each_drv+0x54/0x9a [ 4.531241] [] __device_attach+0xbc/0x162 [ 4.536884] [] device_initial_probe+0xe/0x16 [ 4.542798] [] bus_probe_device+0x7c/0x82 [ 4.548448] [] device_add+0x316/0x77e [ 4.553746] [] usb_set_configuration+0x53e/0x69c [ 4.560014] [] usb_generic_driver_probe+0x46/0x7e [ 4.566367] [] usb_probe_device+0x3e/0xd6 [ 4.572013] [] really_probe+0x94/0x39a [ 4.577388] [] __driver_probe_device+0x76/0x12e [ 4.583549] [] driver_probe_device+0x2c/0xb0 [ 4.589462] [] __device_attach_driver+0x74/0xe0 [ 4.595620] [] bus_for_each_drv+0x54/0x9a [ 4.601270] [] __device_attach+0xbc/0x162 [ 4.606921] [] device_initial_probe+0xe/0x16 [ 4.612834] [] bus_probe_device+0x7c/0x82 [ 4.618484] [] device_add+0x316/0x77e [ 4.623781] [] usb_new_device+0x24e/0x5e8 [ 4.629431] [] hub_event+0xc02/0x170a [ 4.634729] [] process_one_work+0x13c/0x284 [ 4.640539] [] worker_thread+0x7c/0x316 [ 4.645998] [] kthread+0xfe/0x114 [ 4.650951] [] ret_from_exception+0x0/0xc [ 5.039945] eric-tx CALL alloc_txring !!!! [ 5.293738] usb 1-1.3: new low-speed USB device number 5 using xhci-hcd [ 5.353732] ALSA device list: [ 5.356758] #0: Starfive-PWMDAC-Sound-Card [ 5.361085] #1: Starfive-HDMI-Sound-Card [ 5.369922] Freeing unused kernel image (initmem) memory: 2188K [ 5.376264] Run /init as init process [ 5.379983] with arguments: [ 5.382996] /init [ 5.385352] earlyprintk [ 5.388195] with environment: [ 5.391385] HOME=/ [ 5.393822] TERM=linux [ 5.540671] input: Logitech USB Keyboard as /devices/platform/soc/10210000.usbdrd/10100000.usb/xhci-hcd.1.auto/usb1/1-1/1-1.3/1-1.3:1.0/0003:046D:C31D.0001/input/input0 [ 5.540670] EXT4-fs (mmcblk1p4): mounted filesystem with ordered data mode. Opts: (null). Quota mode: disabled. [ 5.634466] hid-generic 0003:046D:C31D.0001: input: USB HID v1.10 Keyboard [Logitech USB Keyboard] on usb-xhci-hcd.1.auto-1.3/input0 [ 5.654954] input: Logitech USB Keyboard Consumer Control as /devices/platform/soc/10210000.usbdrd/10100000.usb/xhci-hcd.1.auto/usb1/1-1/1-1.3/1-1.3:1.1/0003:046D:C31D.0002/input/input1 [ 5.734418] input: Logitech USB Keyboard System Control as /devices/platform/soc/10210000.usbdrd/10100000.usb/xhci-hcd.1.auto/usb1/1-1/1-1.3/1-1.3:1.1/0003:046D:C31D.0002/input/input2 [ 5.751265] hid-generic 0003:046D:C31D.0002: input: USB HID v1.10 Device [Logitech USB Keyboard] on usb-xhci-hcd.1.auto-1.3/input1 [ 6.047438] systemd[1]: systemd 250.5+ running in system mode (+PAM -AUDIT -SELINUX -APPARMOR +IMA -SMACK +SECCOMP -GCRYPT -GNUTLS -OPENSSL -ACL +BLKID -CURL -ELFUTILS -FIDO2 -IDN2 -IDN -IPTC +KMOD -LIBCRYPTSETUP +LIBFDISK -PCRE2 -PWQUALITY -P11KIT -QRENCODE -BZIP2 -LZ4 -XZ -ZLIB +ZSTD -BPF_FRAMEWORK +XKBCOMMON +UTMP +SYSVINIT default-hierarchy=hybrid) [ 6.079246] systemd[1]: Detected architecture riscv64. [ 6.115668] systemd[1]: Hostname set to . [ 6.198668] systemd-sysv-generator[278]: SysV service '/etc/init.d/rc.pvr' lacks a native systemd unit file. Automatically generating a unit file for compatibility. Please update package to include a native systemd unit file, in order to make it more safe and robust. [ 6.528100] systemd[1]: /etc/systemd/system/rc-local.service:11: Support for option SysVStartPriority= has been removed and it is ignored [ 6.695001] systemd[1]: Queued start job for default target Graphical Interface. [ 6.715403] systemd[1]: Created slice Slice /system/getty. [ 6.755158] systemd[1]: Created slice Slice /system/modprobe. [ 6.796197] systemd[1]: Created slice Slice /system/serial-getty. [ 6.834422] systemd[1]: Created slice User and Session Slice. [ 6.874450] systemd[1]: Started Dispatch Password Requests to Console Directory Watch. [ 6.914363] systemd[1]: Started Forward Password Requests to Wall Directory Watch. [ 6.954169] systemd[1]: Reached target Host and Network Name Lookups. [ 6.993927] systemd[1]: Reached target Path Units. [ 7.023807] systemd[1]: Reached target Remote File Systems. [ 7.064027] systemd[1]: Reached target Slice Units. [ 7.104090] systemd[1]: Reached target Swaps. [ 7.156268] systemd[1]: Listening on RPCbind Server Activation Socket. [ 7.194244] systemd[1]: Reached target RPC Port Mapper. [ 7.234307] systemd[1]: Listening on Syslog Socket. [ 7.274574] systemd[1]: Listening on initctl Compatibility Named Pipe. [ 7.320590] systemd[1]: Journal Audit Socket was skipped because of a failed condition check (ConditionSecurity=audit). [ 7.332236] systemd[1]: Listening on Journal Socket (/dev/log). [ 7.375142] systemd[1]: Listening on Journal Socket. [ 7.414442] systemd[1]: Listening on udev Control Socket. [ 7.454840] systemd[1]: Listening on udev Kernel Socket. [ 7.494933] systemd[1]: Listening on User Database Manager Socket. [ 7.537109] systemd[1]: Mounting Huge Pages File System... [ 7.576411] systemd[1]: Mounting POSIX Message Queue File System... [ 7.619087] systemd[1]: Mounting Kernel Debug File System... [ 7.654174] systemd[1]: Kernel Trace File System was skipped because of a failed condition check (ConditionPathExists=/sys/kernel/tracing). [ 7.671145] systemd[1]: Mounting Temporary Directory /tmp... [ 7.711388] systemd[1]: Starting Create List of Static Device Nodes... [ 7.760027] systemd[1]: Starting Load Kernel Module configfs... [ 7.796476] systemd[1]: Starting Load Kernel Module drm... [ 7.837054] systemd[1]: Starting Load Kernel Module fuse... [ 7.885074] systemd[1]: Starting Start psplash boot splash screen... [ 7.929177] systemd[1]: Starting RPC Bind... [ 7.964130] systemd[1]: File System Check on Root Device was skipped because of a failed condition check (ConditionPathIsReadWrite=!/). [ 7.985151] systemd[1]: Starting Journal Service... [ 8.031959] systemd[1]: Load Kernel Modules was skipped because all trigger condition checks failed. [ 8.042790] systemd[1]: Mounting NFSD configuration filesystem... [ 8.086182] systemd[1]: Starting Generate network units from Kernel command line... [ 8.127039] systemd[1]: Starting Remount Root and Kernel File Systems... [ 8.165810] systemd[1]: Starting Apply Kernel Variables... [ 8.205785] systemd[1]: Starting Coldplug All udev Devices... [ 8.215445] Installing knfsd (copyright (C) 1996 okir@monad.swb.de). [ 8.251218] EXT4-fs (mmcblk1p4): re-mounted. Opts: (null). Quota mode: disabled. [ 8.263064] systemd[1]: Started RPC Bind. [ 8.304124] systemd[1]: Started Journal Service. [ 8.991649] systemd-journald[295]: Received client request to flush runtime journal. [ 9.560944] mailbox 13060000.mailbox: Mailbox enabled [ 9.563204] venc: loading out-of-tree module taints kernel. [ 9.574578] SUCCESS alloc_chrdev_region [ 9.606703] cnm_jpu 13090000.jpu: init device. [ 9.613355] vdec 130a0000.vpu_dec: device init. [ 9.617945] SUCCESS alloc_chrdev_region [ 9.690483] mailbox_test soc:mailbox_client@0: invalid resource [ 9.696475] mailbox_test soc:mailbox_client@0: invalid resource [ 9.702545] mailbox_test soc:mailbox_client@0: Successfully registered [ 10.539401] Bluetooth: Core ver 2.22 [ 10.543077] NET: Registered PF_BLUETOOTH protocol family [ 10.548419] Bluetooth: HCI device and connection manager initialized [ 10.554869] Bluetooth: HCI socket layer initialized [ 10.559763] Bluetooth: L2CAP socket layer initialized [ 10.564869] Bluetooth: SCO socket layer initialized [ 10.592474] usbcore: registered new interface driver btusb [ 10.595845] Bluetooth: hci0: RTL: examining hci_ver=0b hci_rev=000b lmp_ver=0b lmp_subver=8852 [ 10.606645] Bluetooth: hci0: RTL: unknown IC info, lmp subver 8852, hci rev 000b, hci ver 000b [ 10.615291] Bluetooth: hci0: RTL: assuming no firmware upload needed [ 11.393645] random: crng init done [ 12.910137] starfive-eth-plat 16030000.ethernet eth0: PHY [stmmac-0:00] driver [YT8531 Gigabit Ethernet] (irq=POLL) [ 12.910604] starfive-eth-plat 16030000.ethernet eth0: Register MEM_TYPE_PAGE_POOL RxQ-0 [ 13.913622] starfive-eth-plat 16030000.ethernet: Failed to reset the dma [ 13.913636] starfive-eth-plat 16030000.ethernet eth0: stmmac_hw_setup: DMA engine initialization failed [ 13.913643] starfive-eth-plat 16030000.ethernet eth0: stmmac_open: Hw setup failed [ 13.933922] starfive-eth-plat 16040000.ethernet eth1: PHY [stmmac-1:00] driver [YT8531 Gigabit Ethernet] (irq=POLL) [ 13.934244] starfive-eth-plat 16040000.ethernet eth1: Register MEM_TYPE_PAGE_POOL RxQ-0 [ 13.934487] dwmac4: Master AXI performs fixed burst length [ 13.934503] starfive-eth-plat 16040000.ethernet eth1: No Safety Features support found [ 13.934518] starfive-eth-plat 16040000.ethernet eth1: IEEE 1588-2008 Advanced Timestamp supported [ 13.934934] starfive-eth-plat 16040000.ethernet eth1: configuring for phy/rgmii-id link mode [ 13.938211] starfive-eth-plat 16040000.ethernet eth1: Link is Up - 1Gbps/Full - flow control rx/tx [ 13.938235] IPv6: ADDRCONF(NETDEV_CHANGE): eth1: link becomes ready [ 14.707343] starfive-eth-plat 16030000.ethernet eth0: PHY [stmmac-0:00] driver [YT8531 Gigabit Ethernet] (irq=POLL) [ 14.708261] starfive-eth-plat 16030000.ethernet eth0: Register MEM_TYPE_PAGE_POOL RxQ-0 [ 15.043651] dwmac4: Master AXI performs fixed burst length [ 15.043676] starfive-eth-plat 16030000.ethernet eth0: No Safety Features support found [ 15.043695] starfive-eth-plat 16030000.ethernet eth0: IEEE 1588-2008 Advanced Timestamp supported [ 15.044160] starfive-eth-plat 16030000.ethernet eth0: configuring for phy/rgmii-id link mode [ 33.834177] mipi_0p9: disabling